Damn Vape DOOM RTA

Atomizers on the grid are gaining popularity, if more precisely, tanks have been prevailing recently in recruits. However, in my environment I do not follow such a trend. In my memory, this is the third such instance that has landed in my “tentacles”, so let’s try to draw some parallels between them.

Damn Vape DOOM RTA

Case material: stainless steel Atomizer
type: RTA
Capacity: 4ml
Diameter: 25mm fit / 26.5mm maximum
Height: 40.5mm with drip type / 33mm without drip type
Connector: 510, pin gilded
Weight: 62g
Color: see photo below

Options
– DOOM RTA
– 2pcs mesh 0.11 / 0.13Ω
– tool for folding the mesh
– cotton
– key
– screwdriver
– spare origins
– spare screws
– spare glass
– spare gaskets
– silicone ring to reduce capacity
– user manual

I can not keep silent about the configuration – it is elegant. Not only do you have everything to start right out of the box., So you also put a special tool for bending the mesh. Fans of the grid will come in handy, although you can safely use improvised items. But agree – it’s nice.

Appearance is quite neat, not particularly catchy. Unless the print on the glass is partly considered a “catchy” decor. At the same time, the dimensions are quite compact – the smallest of the three compared specimens. Well, let’s leave the exterior – yet this is a purely individual matter.

Drip type from plastic, landing 810th. The most common instance, which showed itself quite worthy in the work. Yes, and also – on the inside there is a groove for collecting condensate.

The lid is not threaded, the latter is rather small – getting into this one is sometimes problematic. The risks are islandy, the liquid does not press outward – everything is fine here. The capacity, perhaps, should be called average – there is no possibility of increase – the replacement glass is identical to the pre-installed one. Could a spare tire and without a print do – you never know someone will not like their design.

The shaft diameter is approximately 7.5mm. The evaporation chamber is small, it is made in the form of a regular dome – spherical processing. By the way, traces of processing are visible everywhere on the internal parts, but no burrs or other indecency were found. Here, in the domed part, there are two openings for supplying liquid, they are medium in size, but sufficient.

The deck is quite simple, but there are nuances, but rather innovations. Firstly, it is inserted from the bottom of the tank and is fixed simply by the original and four silicone seals at the edges. After that, the base is put on and now it is already on the thread. There is “dampness” under the base, but it does not penetrate the mod due to the special design of the base.
Familiar deck construct – two non-spring loaded clamping plates for fixing one grid. Screws for a screwdriver, similar spare. There are not so many places for laying cotton; limiters are available.

Three slots can be seen between the plates – here they are for feeding cotton in the middle, and not just around the edges, as is the case with two other competitors. This is a significant plus, since this point is critical when using the grid. But there is another point – our hero is very sensitive to laying cotton wool. First things first, you should not hammer in the grooves for cotton to the bottom – it is necessary to leave just free space so that the slurry calmly follows the central hole. Secondly, do not compact cotton tightly. Usually I don’t resort to the help of my “colleagues”, but here it’s better to see oncethan hear a hundred times.

I will say this – I made three attempts to achieve a “normal” result. Therefore, the decision is only yours – is it interesting for you to poke around and look for the right option. You will have to tinker unequivocally, but after that you can steam up without a break and fear to catch a garik. By the way, the service will not be the most pleasant process for another reason. You will have to first remove the base from the tank, then, twisting it onto the mod, service it. Then again remove from the mod, assemble the atomizer, and only then roll it back.